Experimental measurements from a new single stage turbine are presented. The turbine has 26 vanes and 59 rotating blades with a design point stage expansion ratio of 2.5 and vane exit Mach number of 0.96. A variable sealing flow is supplied to the disk cavity upstream of the rotor and then enters the annulus through a simple axial clearance seal situated on the hub between the stator and rotor. Measurements at the annulus hub wall just downstream of the vanes show the degree of circumferential pressure variation. Further pressure measurements in the disk cavity indicate the strength of the swirling flow in the cavity, and show the effects of mainstream gas ingestion at low sealing flows. Ingestion is further quantified through seeding of the sealing air with nitrous oxide or carbon dioxide and measurement of gas concentrations in the cavity. Interpretation of the measurements is aided by steady and unsteady computational fluid dynamics solutions, and comparison with an elementary model of ingestion.

Issue Section:
Technical Papers
Keywords:
turbines, Mach number, transonic flow, confined flow, computational fluid dynamics, swirling flow
Topics:
Annulus, Cavities, Computational fluid dynamics, Flow (Dynamics), Pressure, Rotors, Sealing (Process), Turbines, Design, Blades, Nozzle guide vanes, Modeling, Pressure measurement, Mach number, Swirling flow
1.
Campbell, D. A., 1978, “Gas Turbine Disc Sealing System Design,” Proc. Conf. on Seal Technology in Gas Turbine Engines, ASME Paper 91-GT-32; AGARD-CP-237.
2.
Abe, T., Kikuchi, J. and Takeuchi, H., 1979, “An Investigation of Turbine Disc Cooling,” Paper GT30, 3rd CIMAC Congress, Vienna.
3.
Kobayashi
,
N.
,
Matsumato
,
M.
, and
Shizuya
,
M.
,
1984
, “
An Experimental Investigation of a Gas Turbine Disc Cooling System
,”
ASME J. Eng. Gas Turbines Power
,
106
, pp.
136
–
141
.
4.
Phadke
,
U. P.
, and
Owen
,
J. M.
,
1988
, “
Aerodynamic Aspects of the Rim Sealing of Gas Turbine Rotor-Stator Systems Parts 1–3
,”
Int. J. Heat Fluid Flow
,
9
, pp.
98
–
117
.
5.
Dadkhah
,
S.
,
Turner
,
A. B.
, and
Chew
,
J. W.
,
1991
, “
Performance of Radial Clearance Rim Seals in Upstream and Downstream Rotor-Stator Wheelspaces,” ASME Paper 91-GT-32; also
ASME J. Turbomachinery
,
114
, pp.
439
–
445
.
6.
Hamabe, K., and Ishida, K., 1992, “Rim Seal Experiments and Analysis of a Rotor-Stator System With Non-Axisymmetric Main Flow,” ASME Paper 92-GT-160.
7.
Chew, J. W., Green, T., and Turner, A. B., 1994, “Rim Sealing of Rotor-Stator Wheelspaces in the Presence of External Flow,” ASME Paper 94-GT-126.
8.
Green, T., and Turner, A. B., 1992, “Ingestion Into the Upstream Wheelspace of an Axial Turbine Stage,” ASME Paper 92-GT-303.
9.
Bohn, D., Rudzinsky, B., Surken, N., and Gartner, W., 2000, “Experimental and Numerical Investigation of the Influence of Rotor Blades on Hot Gas Ingestion Into the Upstream Cavity of an Axial Turbine Stage,” ASME Paper 2000-GT-284.
10.
Roy, R. P., Xu, G., Feng, J., and Kang, S., 2001, “Pressure Field and Main Stream Gas Ingestion in a Rotor Stator Disc Cavity,” ASME Paper 2001-GT-564.
11.
Hills, N. J., Chew, J. W. and Turner, A. B., 2001, “Computational and Mathematical Modelling of Turbine Rim Seal Ingestion,” ASME Paper 2001-GT-204; also, to be published in ASME J. Turbomach.
12.
Turner
,
A. B.
,
Davies
,
S. J.
,
Childs
,
P. R. N.
,
Harvey
,
C. J.
, and
Millward
,
J. A.
, 2000, “Development of a Novel Gas Turbine Driven Centrifugal Compressor,” Proc. Inst. Mech. Eng., 214, Part A.
13.
Von Karman
,
T.
,
1921
, “
Uber Laminare und Turbulente Reibung
,”
Z. Angew. Math. Mech.
,
1
, pp.
233
–
252
.
14.
Pincombe, J. R. and El-Oun, Z., 1986, Unpublished work.
15.
Vaughan, C., 1987, “A Numerical Investigation Into the Effect of an External Flow Field on the Sealing of a rotor-stator Cavity,” Ph.D. thesis, University of Sussex, Brighton, England.
16.
Gambit 1, 1998, Modeling Guide, Fluent Inc.
17.
Fluent 5, 1998, User’s Guide, Fluent Inc.
18.
Hills, N. J., Chew, J. W., Green, T., and Turner, A. B., 1997, “Aerodynamics of Turbine Rim-Seal Ingestion.” ASME Paper 97-GT-268.
Copyright © 2003
 by ASME
You do not currently have access to this content.