The influence of surface roughness on heat transfer coefficient and cooling effectiveness for a fully film cooled three-dimensional nozzle guide vane (NGV) has been measured in a transonic annular cascade using wide band liquid crystal and direct heat flux gages (DHFGs). The liquid crystal methods were used for rough surface measurements and the DHFGs were used for the smooth surfaces. The measurements have been made at engine representative Mach and Reynolds numbers and inlet free-stream turbulence intensity. The aerodynamic and thermodynamic characteristics of the coolant flow have been modeled to represent engine conditions by using a heavy “foreign gas” (30.2 percent and 69.8 percent Ar by weight). Two cooling geometries (cylindrical and fan-shaped holes) have been tested. The strategies of obtaining accurate heat transfer data using a variety of transient heat transfer measurement techniques under the extreme conditions of transonic flow and high heat transfer coefficient are presented. The surfaces of interest are coated with wide-band thermochromic liquid crystals, which cover the range of NGV surface temperature variation encountered in the test. The liquid crystal has a natural peak-to-peak roughness height of 25 μm creating a transitionally rough surface on the NGV. The time variation of color is processed to give distributions of both heat transfer coefficient and film cooling effectiveness over the NGV surface. The NGV was first instrumented with the DHFGs and smooth surface tests preformed. Subsequently the surface was coated with liquid crystals for the rough surface tests. The DHFGs were then employed as the means of calibrating the liquid crystal layer. The roughness of 25 μm, which is the typical order of roughness for the in-service turbine blades and vanes, increases the heat transfer coefficient by up to 50 percent over the smooth surface level. The film cooling effectiveness is influenced less by the roughness. [S0889-504X(00)00804-7]
Skip Nav Destination
Article navigation
October 2000
Technical Papers
Influence of Surface Roughness on Heat Transfer and Effectiveness for a Fully Film Cooled Nozzle Guide Vane Measured by Wide Band Liquid Crystals and Direct Heat Flux Gages
S. M. Guo,
S. M. Guo
Department of Engineering Science, University of Oxford, Oxford, England
Search for other works by this author on:
C. C. Lai,
C. C. Lai
Department of Engineering Science, University of Oxford, Oxford, England
Search for other works by this author on:
T. V. Jones,
T. V. Jones
Department of Engineering Science, University of Oxford, Oxford, England
Search for other works by this author on:
M. L. G. Oldfield,
M. L. G. Oldfield
Department of Engineering Science, University of Oxford, Oxford, England
Search for other works by this author on:
G. D. Lock,
G. D. Lock
Department of Mechanical Engineering, University of Bath, Bath, England
Search for other works by this author on:
A. J. Rawlinson
A. J. Rawlinson
Rolls-Royce plc, Derby, England
Search for other works by this author on:
S. M. Guo
Department of Engineering Science, University of Oxford, Oxford, England
C. C. Lai
Department of Engineering Science, University of Oxford, Oxford, England
T. V. Jones
Department of Engineering Science, University of Oxford, Oxford, England
M. L. G. Oldfield
Department of Engineering Science, University of Oxford, Oxford, England
G. D. Lock
Department of Mechanical Engineering, University of Bath, Bath, England
A. J. Rawlinson
Rolls-Royce plc, Derby, England
Contributed by the International Gas Turbine Institute and presented at the 45th International Gas Turbine and Aeroengine Congress and Exhibition, Munich, Germany, May 8–11, 2000. Manuscript received by the International Gas Turbine Institute February 2000. Paper No. 2000-GT-204. Review Chair: D. Ballal.
J. Turbomach. Oct 2000, 122(4): 709-716 (8 pages)
Published Online: February 1, 2000
Article history
Received:
February 1, 2000
Citation
Guo , S. M., Lai , C. C., Jones , T. V., Oldfield, M. L. G., Lock, G. D., and Rawlinson, A. J. (February 1, 2000). "Influence of Surface Roughness on Heat Transfer and Effectiveness for a Fully Film Cooled Nozzle Guide Vane Measured by Wide Band Liquid Crystals and Direct Heat Flux Gages ." ASME. J. Turbomach. October 2000; 122(4): 709–716. https://doi.org/10.1115/1.1312798
Download citation file:
Get Email Alerts
Related Articles
A Converging Slot-Hole Film-Cooling Geometry—Part 2: Transonic Nozzle Guide Vane Heat Transfer and Loss
J. Turbomach (July,2002)
Channel Height Effect on Heat Transfer and Friction in a Dimpled Passage
J. Eng. Gas Turbines Power (April,2000)
A Novel Technique for Assessing Turbine Cooling System Performance
J. Turbomach (July,2011)
Effects of a Reacting Cross-Stream on Turbine Film Cooling
J. Eng. Gas Turbines Power (May,2010)
Related Proceedings Papers
Related Chapters
Thermal Interface Resistance
Thermal Management of Microelectronic Equipment
Adding Surface While Minimizing Downtime
Heat Exchanger Engineering Techniques
Chitosan-Based Drug Delivery Systems
Chitosan and Its Derivatives as Promising Drug Delivery Carriers