Abstract

Because mechanical properties of structural materials for high-temperature use, such as boiler tubing, degrade during long-term service, it is essential to detect toughness degradation by means of a nondestructive and simple field test technique. A grain boundary etching technique is developed to detect material degradation, and assess creep strength and notch toughness. An etching test using a picric acid solution with a wetting agent or using 20 percent HNO3 with alcoholic solution was found to have great potential for the nondestructive estimation of grain boundary embrittlement caused by carbide and sigma precipitation in SUS stainless steel. The feasibility of this estimation procedure was determined showing the relationships between Charpy impact energy (CVN) and grooving width (WGS), and creep damage ratio (Φ) and WGS. Superheater tubes of fossil fuel boiler were tested on site to demonstrate the validity of this technique.

Issue Section:
Research Papers
Topics:
Boiler tubes, Creep, Damage, Fossil fuels, Etching, Fracture toughness, Grain boundaries, Boilers, Embrittlement, High temperature, Materials degradation, Mechanical properties, Precipitation, Stainless steel, Superheaters, Wetting agents
1.
Cleary
J. J.
, and
Green
N. D.
,
1967
, “
Corrosion Properties of Iron and Steel
,”
Corrosion Science
, Vol.
7
, pp.
821
–
831
.
2.
Nogata
F.
,
Seo
K.
,
Masaki
J.
,
Kawano
K.
,
Yaegashi
A.
, and
Chung
S. H.
,
1987
, “
Nondestructive Evaluation for In-Service Material Degradation of High Temperature Structural Components by Using Grain Boundary Etching Method
,” (in Japanese),
Journal of Japanese Society for Nondestructive Inspection
, Vol.
36
, pp.
535
–
539
.
3.
Nogata, F., Seo, K., Chung, S. H., Lee, J. J., and Takahashi, H., 1990, “Standardization of Grain Boundary Etching Test Method for Evaluating High Temperature Material Degradation,” Proceedings, KSME/JSME Joint Conference Fracture and Strength, Seoul, Korea, pp. 328–333; also Transtech Publications, pp. 246–252.
4.
Nogata
F.
,
Seo
K.
,
Takahashi
H.
,
Tamagawa
K.
, and
Chung
S. H.
,
1991
, “
Evaluation of Material Degradation in In-Service High Temperature Structural Component by a Chemical Etching Test
,”
International Journal of Pressure Vessel and Piping
, Vol.
45
, pp.
367
–
379
.
5.
Ogura
T.
,
Makino
A.
, and
Masumoto
T.
,
1980
, “
Comparison of Auger Electron Spectroscopy and Etching Method for Analysis of Grain Boundary Segregation of Phosphorus
,”
Scripta Metallurgica
, Vol.
14
, pp.
887
–
889
.
6.
Ogura
T.
,
Makino
A.
, and
Masumoto
T.
,
1984
, “
A Grain Boundary Etching Method for the Analysis of Intergranuiar P-Segregation in Ironbased Alloys
,”
Metallurgical Transaction
, Vol.
15A
, pp.
1563
–
1570
.
7.
Saito, Y., 1986, “Materials Degradation and Its Relevance to Life Assessment of Superheater Tubes of Fossil Boilers,” Proceedings, Conference on Life Extension and Assessment of Fossil Plants, EPRI, EEI, ASME, and ASM, Washington, D.C.
8.
Saito, Y., 1989, “Correlation Between Microstructure Analysed by Means of Image Processing Technique and Electrochemical Polarization Parameter of Superheater Tubes of Fossil Boilers,” Nondestructive Evaluation Planning and Application, ASME Pressure Vessel and Piping Conference, Honolulu, HI, Vol. 5, pp. 237–242.
This content is only available via PDF.
Copyright © 1995
 by The American Society of Mechanical Engineers
You do not currently have access to this content.