This paper presents the failure pattern, the ultimate strength, and the stress concentration factor of unstiffened T-joints obtained from experimental and numerical investigations conducted on them under axial brace compression loading. The numerical modeling was performed on the whole joint using ANSYS software package. This modeling has predicted the ultimate strength accurately when compared with that of the conventional modeling of only a portion of the joint. The nominal diameter and thickness of the chord of the unstiffened T-joints were 324 mm and 12 mm, respectively, and the corresponding values of the brace were 219 mm and 8 mm, respectively. The T-joint was approximately one-fourth the size of the largest joints in the platforms built in a shallow water depth of 80 m in the Bombay High field. The bending of the whole chord member combined with punching shear failure due to its ovalization was observed to be the predominant behavior of the unstiffened joint. The numerical analysis has simulated the behavior of the joint as was observed in the experiment and has also helped establish its correct failure pattern. It was also observed in these investigations that the unstiffened joint was stiffer in ovalization mode than in flexural deflection. The results obtained from the numerical modeling were observed, in general, to be in good agreement with that obtained from the testing. The stress concentration factor predicted by the numerical analysis is in close agreement with that measured in the experiment as well as that computed using well established parametric equations.
Skip Nav Destination
Article navigation
November 2009
Materials
Experimental and Numerical Investigations on Unstiffened Tubular T-Joints of Offshore Platforms
T. S. Thandavamoorthy
T. S. Thandavamoorthy
Dean
Department of Civil Engineering,
Dr. M. G. R. University
, Chennai 600 095, India
Search for other works by this author on:
T. S. Thandavamoorthy
Dean
Department of Civil Engineering,
Dr. M. G. R. University
, Chennai 600 095, IndiaJ. Offshore Mech. Arct. Eng. Nov 2009, 131(4): 041401 (7 pages)
Published Online: October 2, 2009
Article history
Received:
November 18, 2007
Revised:
March 31, 2009
Published:
October 2, 2009
Citation
Thandavamoorthy, T. S. (October 2, 2009). "Experimental and Numerical Investigations on Unstiffened Tubular T-Joints of Offshore Platforms." ASME. J. Offshore Mech. Arct. Eng. November 2009; 131(4): 041401. https://doi.org/10.1115/1.3160422
Download citation file:
Get Email Alerts
Cited By
Numerical Modeling of Fish Cage Structural Responses in Regular and Irregular Waves Using Modified XPBD
J. Offshore Mech. Arct. Eng (April 2025)
Layout Optimization of Wave Energy Park Based on Multi-Objective Optimization Algorithm
J. Offshore Mech. Arct. Eng (August 2025)
Effects of Aerodynamic Damping and Gyroscopic Moments on Dynamic Responses of a Semi-Submersible Floating Vertical Axis Wind Turbine: An Experimental Study
J. Offshore Mech. Arct. Eng (April 2025)
Investigating the Impact of System Parameters on Flow-Induced Vibration Hard Galloping Based on Deep Neural Network
J. Offshore Mech. Arct. Eng (August 2025)
Related Articles
Investigations on Internally Ring-Stiffened Joints of Offshore Platforms
J. Offshore Mech. Arct. Eng (November,2000)
Finite-Element Modelling of Multi-Planar Offshore Tubular Joints
J. Offshore Mech. Arct. Eng (February,2004)
Optimizing Ultrasonic Additive Manufactured Al 3003 Properties With Statistical Modeling
J. Eng. Mater. Technol (January,2012)
Impact Resistance of SM Joints Formed With ICA
J. Electron. Packag (December,2002)
Related Proceedings Papers
Related Chapters
Compromise between Tensile and Fatigue Strength
New Advanced High Strength Steels: Optimizing Properties
Common Compliant Platforms
Offshore Compliant Platforms: Analysis, Design, and Experimental Studies
On the Exact Analysis of Non-Coherent Fault Trees: The ASTRA Package (PSAM-0285)
Proceedings of the Eighth International Conference on Probabilistic Safety Assessment & Management (PSAM)