The long fatigue life is the one of the most important criterion for the design of rolling bearings, however, due to complex and diverse internal geometries, each type of rolling bearings require a different design formulation. To increase the life of cylindrical roller bearings, the profile (or the crowning) of the roller plays an important role. A flat profile of the rolling element results in the edge stress concentrations at roller ends. A circular crowning of roller eliminates the edge stress concentration at the lower and moderate loads only; however, it develops edge stress concentrations at heavy loads. The logarithmic profile of the roller results in no edge stress concentration at the low, medium, and heavy loads; distribution of contact stresses is also nearly uniform along the length of the roller. A design methodology for the optimum design of cylindrical roller bearings with the logarithmic profile has been outlined. A nonlinear constrained optimization problem has been formulated for the design of cylindrical roller bearings with logarithmic profiles and is optimized by using real-coded genetic algorithms. The change in roller profile has not been accounted for explicitly in the standard definition of the dynamic capacity; hence, for the present case directly the Lundberg–Palmgren life equation has been chosen as an objective function. Design variables include four bearing geometrical parameters and the two logarithmic profile generating parameters are considered. In addition to these, another five design constraint constants are also included, which indirectly affect the fatigue life of cylindrical roller bearings. The five design constraint constants have been given bounds based on the parametric studies through initial optimization runs. The effective length of the roller is taken corresponding to the standard roller diameter, which has standard discrete dimensions. Constraint violation study has been performed to have an assessment of the effectiveness of each of the constraints. A convergence study has been carried out to ensure the global optimum point in the design. A sensitivity analysis of various geometric design parameters has been performed using the Monte Carlo simulation technique, in order to see changes in the fatigue life of the bearing. Illustrations show that the multiplier of the logarithmic profile deviation parameter has more effect on the fatigue life as compared with other geometric parameters.

1.
Seireg
,
A.
, and
Ezzat
,
H.
, 1969, “
Optimum Design of Hydrodynamic Journal Bearings
,”
ASME J. Lubr. Technol.
0022-2305,
91
(
3
), pp.
516
523
.
2.
Maday
,
C. J.
, 1970, “
The Maximum Principle Approach to the Optimum One-Dimensional Journal Bearing
,”
ASME J. Lubr. Technol.
0022-2305,
92
(
2
), pp.
482
489
.
3.
Wylie
,
G. M.
, and
Maday
,
C. J.
, 1970, “
The Optimum One-Dimensional Hydrodynamic Gas Rayleigh Step Bearing
,”
ASME J. Lubr. Technol.
0022-2305,
92
(
3
), pp.
504
508
.
4.
Hirani
,
H.
,
Athre
,
K.
, and
Biswas
,
S.
, 2000, “
Comprehensive Design Methodology for an Engine Journal Bearing
,”
Proc. Inst. Mech. Eng., Part J: J. Eng. Tribol.
1350-6501,
214
, pp.
401
412
.
5.
Changsen
,
W.
, 1991,
Analysis of Rolling Element Bearings
,
Mechanical Engineering
,
London
.
6.
Horng
,
T. L.
,
Ju
,
S. H.
, and
Cha
,
K. C.
, 2000, “
A Deformation Formula for Circular Crowned Roller Compressed Between Two Flat Plates
,”
ASME J. Tribol.
0742-4787,
122
, pp.
405
411
.
7.
Harris
,
T. A.
, 2001,
Rolling Bearing Analysis
,
Wiley
,
New York
.
8.
Holland
,
J. H.
, 1965,
Adaptation in Natural and Artificial Systems
,
University of Michigan
,
Ann Arbor
.
9.
Goldberg
,
D. E.
, 1989,
Genetic Algorithms in Search, Optimization and Machine Learning
,
Addison-Wesley
,
Reading, MA
.
10.
Chakraborty
,
I.
,
Kumar
,
V.
,
Nair
,
S. B.
, and
Tiwari
,
R.
, 2003, “
Rolling Element Bearing Design Through Genetic Algorithm
,”
Eng. Optimiz.
0305-215X,
35
(
6
), pp.
649
659
.
11.
Chaturbhuj
,
N.
,
Nair
,
S. B.
, and
Tiwari
,
R.
, 2003, “
Design Optimization for Tapered Roller Bearings Using Genetic Algorithm
,”
Proceedings of the International Conference on Artificial Intelligence, IC-AI‘03
, Las Vegas, NV, Jun. 23–26, 2003,
CSREA
,
Nevada
, Vol.
1
, pp.
421
427
.
12.
Rao
,
R. B.
, and
Tiwari
,
R.
, 2007, “
Optimum Design of Rolling Element Bearings Using Genetic Algorithms
,”
Mech. Mach. Theory
0094-114X,
42
(
2
), pp.
233
250
.
13.
SKF
, 2005, General Catalogue, Media print, Germany.
14.
Kania
,
L.
, 2006, “
Modeling of Rollers in Calculation of Slewing Bearing With the Use of Finite Elements
,”
Mech. Mach. Theory
0094-114X,
41
, pp.
1359
1376
.
15.
Krzemin’ski-Freda
,
H.
, 1992, “
The Logarithmic Correction Optimization of Roller Generators in Roller Bearings
,”
Tribol. Int.
0301-679X,
13
(
3
), pp.
56
61
.
16.
Lundberg
,
G.
, and
Palmgren
,
A.
, 1947, “
Dynamic Capacity of Rolling Bearings
,”
Acta Polytechnica Mechanical Engineering Series
, 1, 3, Stockholm.
17.
Poplawski
,
V.
,
Zaretsky
,
V.
, and
Peters
,
M.
, 2000, “
Effect of Roller Profile on Cylindrical Roller Bearing Life Prediction
,” NASA/TM-2000-210368.
18.
Deb
,
K.
, 2003,
Multi Objective Optimization for Engineering Design Algorithms
,
Prentice-Hall
,
New Delhi, India
.
19.
Deb
,
K.
, and
Tiwari
,
S.
, 2008, “
Omni-Optimizer: A Generic Evolutionary Algorithm for Single and Multi-Objective Optimization
,”
Eur. J. Oper. Res.
0377-2217,
185
, pp.
1062
1087
.
20.
Herrera
,
F.
,
Lozano
,
M.
, and
Verdegay
,
J. L.
, 1998, “
Tackling Real-Coded Genetic Algorithms: Operators and Tools for Behavioral Analysis
,”
Artif. Intell. Rev.
0269-2821,
12
, pp.
265
319
.
You do not currently have access to this content.