Fatigue crack growth and related damage mechanisms were investigated experimentally in a stainless steel/aluminum laminated composite with middle through thickness crack, and two different fracture mechanics approaches applied to the composite to reveal their differences under fatigue loading. The laminated composite material, which has a unidirectional continuous AISI 304 stainless steel as fibers and Al 1060 as matrix, was produced by using diffusion bonding. Fatigue tests were conducted in accordance with ASTM E 647. The relationships between fatigue crack growth rate (da/dN), stress intensity factor , and strain energy release rate were determined; and damage behavior was discussed. Both linear elastic fracture mechanics (LEFM) and compliance method were used, and the results were compared with each other. It is found that as the crack propagates, the LEFM overestimates the values. Interlaminar and fiber/matrix interface damage were evaluated by fractographic examination.
Skip Nav Destination
e-mail: veskizeybek@selcuk.edu.tr
Article navigation
April 2011
Research Papers
Fatigue Behavior and Damage Assessment of Stainless Steel/Aluminum Composites
Volkan Eskizeybek,
Volkan Eskizeybek
Department of Mechanical Engineering,
e-mail: veskizeybek@selcuk.edu.tr
Selçuk University
, 42075 Kampus/Konya, Turkey
Search for other works by this author on:
Ahmet Avci,
Ahmet Avci
Department of Mechanical Engineering,
Selçuk University
, 42075 Kampus/Konya, Turkey
Search for other works by this author on:
Ahmet Akdemir,
Ahmet Akdemir
Department of Mechanical Engineering,
Selçuk University
, 42075 Kampus/Konya, Turkey
Search for other works by this author on:
Ömer Sinan Şahin
Ömer Sinan Şahin
Department of Mechanical Engineering,
Selçuk University
, 42075 Kampus/Konya, Turkey
Search for other works by this author on:
Volkan Eskizeybek
Department of Mechanical Engineering,
Selçuk University
, 42075 Kampus/Konya, Turkeye-mail: veskizeybek@selcuk.edu.tr
Ahmet Avci
Department of Mechanical Engineering,
Selçuk University
, 42075 Kampus/Konya, Turkey
Ahmet Akdemir
Department of Mechanical Engineering,
Selçuk University
, 42075 Kampus/Konya, Turkey
Ömer Sinan Şahin
Department of Mechanical Engineering,
Selçuk University
, 42075 Kampus/Konya, TurkeyJ. Eng. Mater. Technol. Apr 2011, 133(2): 021016 (5 pages)
Published Online: March 21, 2011
Article history
Received:
September 5, 2010
Revised:
January 20, 2011
Online:
March 21, 2011
Published:
March 21, 2011
Citation
Eskizeybek, V., Avci, A., Akdemir, A., and Şahin, Ö. S. (March 21, 2011). "Fatigue Behavior and Damage Assessment of Stainless Steel/Aluminum Composites." ASME. J. Eng. Mater. Technol. April 2011; 133(2): 021016. https://doi.org/10.1115/1.4003490
Download citation file:
Get Email Alerts
Cited By
Modeling Growth and Viscous Flow of Oxide on Cylindrical Silicon Surfaces Including Piezoviscous Inhibition
J. Eng. Mater. Technol (April 2025)
Thermal Conductivity of 3D-Printed Metal Using Extrusion-Based Metal Additive Manufacturing Process
J. Eng. Mater. Technol (April 2025)
Related Articles
Fatigue Characterization and Modeling of Friction Stir Spot Welds in Magnesium AZ31 Alloy
J. Eng. Mater. Technol (October,2010)
Fracture Mechanics and Fractography of Creep and Fatigue Crack Propagation at Elevated Temperature
J. Eng. Mater. Technol (October,1976)
The Effect of Biaxial Stresses on Fatigue and Fracture
J. Eng. Ind (November,1970)
A Statistically Based Investigation of the Environmental and Cyclic Stress Effects on Fretting Fatigue
J. Eng. Mater. Technol (July,1981)
Related Proceedings Papers
Related Chapters
Introduction and Definitions
Handbook on Stiffness & Damping in Mechanical Design
A Fracture Mechanics Method for an Advanced Evaluation of Inclusions and the Prediction of Fatigue Life of Rolling Element Bearings
Bearing and Transmission Steels Technology
Fatigue Testing of Hydrogen-Exposed Austenitic Stainless Steel Welded Samples
International Hydrogen Conference (IHC 2012): Hydrogen-Materials Interactions