We have developed a model capable of predicting the performance characteristics of a wiretype Joule–Thomson microcooler intended for use within a cryosurgical probe. Our objective was to be able to predict cold tip temperature, temperature distribution, and cooling power using only inlet gas properties as input variables. To achieve this, the model incorporated gas equations of state to account for changing gas properties due to heat transfer within the heat exchanger and expansion within the capillary. In consideration of inefficiencies, heat in-leak from free convection and radiation was also considered and the use of a 2D axisymmetric finite difference code allowed simulation of axial conduction. To validate simulation results, we have constructed and conducted experiments with two types of microcoolers differing in inner tube material, poly-ether-ether-ketone (PEEK) and stainless steel. The parameters of the experiment were used in the calculations. CO2 was used as the coolant gas for inlet pressures from 0.5 MPa to 2.0 MPa. Heat load trials of up to 550 mW along with unloaded trials were conducted. The temperature measurements show that the model was successfully able to predict the cold tip temperature to a good degree of accuracy and well represent the temperature distribution. For the all PEEK microcooler in a vacuum using 2.0 MPa inlet pressure, the calculations predicted a temperature drop of 57 K and mass flow rate of 19.5 mg/s compared to measured values of 63 K and 19.4 mg/s, therefore, showing that conventional macroscale correlations can hold well for turbulent microscale flow and heat transfer as long as the validity of the assumptions is verified.
Skip Nav Destination
e-mail: adhikayev@gmail.com
Article navigation
Heat Transfer In Nanochannels, Microchannels, And Minichannels
Theoretical and Experimental Study of a Flexible Wiretype Joule–Thomson Microrefrigerator for Use in Cryosurgery
Adhika Widyaparaga,
Adhika Widyaparaga
Department of Mechanical Engineering, Kyushu University, 744 Motooka, Nishi-ku, Fukuoka 819-0395, Japan; Department of Mechanical and Industrial Engineering,
e-mail: adhikayev@gmail.com
Gadjah Mada University
, Jl. Grafika 2, Yogyakarta 55281, Indonesia
Search for other works by this author on:
Masashi Kuwamoto,
Masashi Kuwamoto
Department of Mechanical Engineering,
Kyushu University
, 744 Motooka, Nishi-ku, Fukuoka 819-0395, Japan
Search for other works by this author on:
Naoya Sakoda,
Naoya Sakoda
International Research Center for Hydrogen Energy,
Kyushu University
, 744 Motooka, Nishi-ku, Fukuoka 819-0395, Japan
Search for other works by this author on:
Masamichi Kohno,
Masamichi Kohno
Department of Mechanical Engineering; International Institute for Carbon-Neutral Energy Research,
Kyushu University
, 744 Motooka, Nishi-ku, Fukuoka 819-0395, Japan
Search for other works by this author on:
Yasuyuki Takata
Yasuyuki Takata
Department of Mechanical Engineering; International Institute for Carbon-Neutral Energy Research,
Kyushu University
, 744 Motooka, Nishi-ku, Fukuoka 819-0395, Japan
Search for other works by this author on:
Adhika Widyaparaga
Department of Mechanical Engineering, Kyushu University, 744 Motooka, Nishi-ku, Fukuoka 819-0395, Japan; Department of Mechanical and Industrial Engineering,
Gadjah Mada University
, Jl. Grafika 2, Yogyakarta 55281, Indonesia
e-mail: adhikayev@gmail.com
Masashi Kuwamoto
Department of Mechanical Engineering,
Kyushu University
, 744 Motooka, Nishi-ku, Fukuoka 819-0395, Japan
Naoya Sakoda
International Research Center for Hydrogen Energy,
Kyushu University
, 744 Motooka, Nishi-ku, Fukuoka 819-0395, Japan
Masamichi Kohno
Department of Mechanical Engineering; International Institute for Carbon-Neutral Energy Research,
Kyushu University
, 744 Motooka, Nishi-ku, Fukuoka 819-0395, Japan
Yasuyuki Takata
Department of Mechanical Engineering; International Institute for Carbon-Neutral Energy Research,
Kyushu University
, 744 Motooka, Nishi-ku, Fukuoka 819-0395, Japan
J. Heat Transfer. Feb 2012, 134(2): 020903 (7 pages)
Published Online: December 13, 2011
Article history
Received:
January 9, 2011
Revised:
August 8, 2011
Online:
December 13, 2011
Published:
December 13, 2011
Citation
Widyaparaga, A., Kuwamoto, M., Sakoda, N., Kohno, M., and Takata, Y. (December 13, 2011). "Theoretical and Experimental Study of a Flexible Wiretype Joule–Thomson Microrefrigerator for Use in Cryosurgery." ASME. J. Heat Transfer. February 2012; 134(2): 020903. https://doi.org/10.1115/1.4004937
Download citation file:
Get Email Alerts
Cited By
Estimation of thermal emission from mixture of CO2 and H2O gases and fly-ash particles
J. Heat Mass Transfer
Non-Classical Heat Transfer and Recent Progress
J. Heat Mass Transfer
Related Articles
Natural Convection From a Tube Bundle in a Thin Inclined Enclosure
J. Sol. Energy Eng (May,2004)
Film Cooling of a Cylindrical Leading Edge With Injection Through Rows of Compound-Angle Holes
J. Heat Transfer (August,2001)
A Numerical Study of the Thermal Performance of a Tape Ball Grid Array (TBGA) Package
J. Electron. Packag (June,2000)
Heat Transfer of Supercritical Carbon Dioxide in Printed Circuit Heat Exchanger Geometries
J. Thermal Sci. Eng. Appl (September,2011)
Related Chapters
Experimental Investigation of an Improved Thermal Response Test Equipment for Ground Source Heat Pump Systems
Inaugural US-EU-China Thermophysics Conference-Renewable Energy 2009 (UECTC 2009 Proceedings)
Natural Gas Transmission
Pipeline Design & Construction: A Practical Approach, Third Edition
Applications
Introduction to Finite Element, Boundary Element, and Meshless Methods: With Applications to Heat Transfer and Fluid Flow