This paper presents a study of pressure drops during condensation inside a smooth, an 18-deg helical microfin, and a herringbone microfin tube. Measurements were conducted with refrigerant flowing through the tube of a concentric heat exchanger, with water flowing in a counterflow direction in the annulus. Each tube was part of a condenser consisting of eight subcondensers with instrumentation preceding each subcondenser. Three refrigerants were used, namely, R-22, R-407C, and R-134a, all operating at a saturation temperature of 40 °C with mass fluxes ranging from 400 to 800kg/m2 s. Inlet qualities ranged from 0.85 to 0.95 and outlet qualities ranged from 0.05 to 0.15. The test results showed that on average for the three refrigerants the pressure gradients of the herringbone microfin tube were about 79% higher than that of the smooth tube and about 27% higher than that of the helical microfin tube. Further, a correlation from the literature for predicting pressure drops inside a helical microfin tube was modified for the herringbone microfin tube. The modified correlation predicted the data to within an error of 1% and had an absolute mean deviation of 6.8%. This modified correlation compared well with a correlation from the literature that predicted the data to within an error of 7%.

Issue Section:
Evaporation, Boiling, and Condensation
Keywords:
water, two-phase flow, pipe flow, refrigerants, heat exchangers, condensation, Refrigerant Condensation, Smooth Tube, Helical Microfin Tube, Herringbone Microfin Tube, Pressure Drop, Flow Regime
Topics:
Pressure drop, Refrigerants, Condensation, Flow (Dynamics)
1.
Liebenberg, L., 2002, “A Unified Prediction Method for Condensation Performance in Smooth and Microfin Tubes,” Ph.D. thesis, Rand Afrikaans University, Johannesburg.
2.
Miyara
,
A.
,
Otsubo
,
Y.
,
Ohtsuka
,
S.
, and
Mizuta
,
Y.
,
2003
, “
Effects of Fin Shape on Condensation in Herringbone Microfin Tubes
,”
Int. J. Refrig.
,
26
, pp.
417
–
424
.
3.
Ebisu
,
T.
, and
Torikoshi
,
K.
,
1998
, “
Experimental Study on Evaporation and Condensation Heat Transfer Enhancement for R-407C Using Herringbone Heat Transfer Tube
,”
ASHRAE Trans.
,
104
(
2
), pp.
1044
–
1052
.
4.
Miyara
,
A.
,
Nonaka
,
K.
, and
Taniguchi
,
M.
,
2000
, “
Condensation Heat Transfer and Flow Pattern Inside a Herringbone-Type Microfin Tube
,”
Int. J. Refrig.
,
23
, pp.
141
–
152
.
5.
Goto
,
N.
,
Inoue
,
N.
, and
Ishiwatari
,
N.
,
2001
, “
Condensation and Evaporation Heat Transfer of R-410A inside Internally Grooved Horizontal Tubes
,”
Int. J. Refrig.
,
24
, pp.
628
–
638
.
6.
Kline
,
S. J.
, and
McClintock
,
F. A.
,
1953
, “
Describing Uncertainties in Single-Sample Experiments
,”
Mech. Eng. (Am. Soc. Mech. Eng.)
,
75
, pp.
3
–
8
.
7.
REFPROP, 1999, “NIST Thermodynamic Properties of Refrigerants and Refrigerant Mixtures (REFPROP),” Version 6.0, NIST Standard Reference Database 23, National Institute of Standards and Technology, Gaithersburg, MD.
8.
Rouhani
,
S. Z.
, and
Axelsson
,
E.
,
1970
, “
Calculation of Volume Void Fraction in the Subcooled and Quality Region
,”
Int. J. Heat Mass Transfer
,
13
, pp.
383
–
393
.
9.
Thome, J. R., 2003, “On Recent Advances in Modeling of Two-Phase Flow and Heat Transfer,” Heat Transfer Engineering, 24(6), pp. 46–59.
10.
Lockhart
,
R. W.
, and
Martinelli
,
R. C.
,
1949
, “
Proposed Correlation of Data for Isothermal Two-Phase, Two-Component Flow in Pipe
,”
Chem. Eng. Prog.
,
45
, pp.
39
–
48
.
11.
Cavallini
,
A.
,
Del Col
,
D.
,
Doretti
,
L.
,
Longo
,
G. A.
, and
Rossetto
,
L.
,
2000
, “
Heat Transfer and Pressure Drop During Condensation of Refrigerants Inside Horizontal Enhanced Tubes
,”
Int. J. Refrig.
,
23
, pp.
4
–
25
.
12.
Owaga, D. C., 2003, “Flow Patterns during Refrigerant Condensation in Smooth and Enhanced Tubes,” Master’s dissertation, Rand Afrikaans University, Johannesburg.
13.
Liebenberg, L., Thome, J. R., and Meyer, J. P., 2004, “Flow Pattern Identification With Power Spectral Density Distributions of Pressure Traces During Refrigerant Condensation in Smooth and Microfin Tubes,” ASME J. Heat Transfer, submitted for review.
14.
Wang
,
J.
,
Lan
,
S.
, and
Chen
,
G.
,
2000
, “
Experimental Study on the Turbulent Boundary Layer Flow Over Riblets Surface
,”
Fluid Dyn.
,
27
(
4
), pp.
217
–
229
.
15.
Carnavos
,
T. C.
,
1980
, “
Heat Transfer Performance of Internally Finned Tubes in Turbulent Flow
,”
Heat Transfer Eng.
,
4
(
1
), pp.
32
–
37
.
16.
Souza, A. L., and Pimenta, M. M., 1995, “Prediction of Pressure Drop During Horizontal Two-Phase Flow of Pure and Mixed Refrigerants,” ASME Conference on Cavitation and Multiphase Flow, ASME, New York, Vol. 210, pp. 161–171.
17.
Friedel, L., 1979, “Improved Friction Pressure Drop Correlation for Horizontal and Vertical Two-phase Two-component Flow in Pipes,” E2, European Two-Phase Flow Group Meeting, Ispra.
18.
Azer, N. Z., and Said, S. A., 1982, “Augmentation of Condensation Heat Transfer by Internally Finned Tubes and Twisted Tape Inserts,” Proc. of 7th Int. Heat Transfer Conference, Mu¨nchen, West-Germany, Hemisphere, 5, pp. 33–38.
19.
Haraguchi
,
H.
,
Koyama
,
S.
, and
Fujii
,
T.
,
1994
, “
Condensation of Refrigerants HCFC22, HFC134a and HCFC123 in a Horizontal Smooth Tube: 1st Report, Proposals of Empirical Expressions for the Local Frictional Pressure Drop
,”
Trans. JSME
,
60
, pp.
2111
–
2116
.
Copyright © 2004
 by ASME
You do not currently have access to this content.