A general form of the stress-strain constitutive relation was introduced for the application of two nonlinear turbulence models, namely, the algebraic Reynolds stress model of Gatski and Speziale (1993, “On Explicit Algebraic Stress Models for Complex Turbulent Flows,” J. Fluid Mech., 254, pp. 59–78) and the cubic model of Lien et al. (1996, “Low Reynolds Number Eddy-Viscosity Modeling Based on Non-Linear Stress-Strain/Vorticity Relations,” Proceedings of Third Symposium on Engineering Turbulence Modeling and Measurements, Crete, Greece), to the numerical analysis of flow fields in a test engine with flat-piston and bowl-in-piston arrangements, under swirling and no-swirling flow motored conditions. The model capabilities in capturing turbulent flow features were compared to those of the upgraded linear RNG model, which was previously indicated as a good compromise between accuracy and computational cost. Evaluations were made on the basis of the predicted flow evolution throughout the whole engine cycle, as well as of the comparison between the numerical and experimental results. Furthermore, the effect of the stress-strain relationship on the predicted averaged turbulence quantities and anisotropy-invariant values were examined, in addition to the sensitivity of the nonlinear models to the mesh quality. Finally, prospects concerning possible improvements of turbulence eddy-viscosity models were presented. The predictions were made by a newly developed CFD code embedding various accuracy-order finite-volume discretization schemes. Modified wall boundary conditions with respect to the conventional logarithmic-function approach were used, so as to make the local equilibrium hypothesis virtually ineffective.
Skip Nav Destination
Article navigation
November 2008
Research Papers
Nonlinear Versus Linear Stress-Strain Relations in Engine Turbulence Modeling Under Swirl and Squish Flow Conditions
Mirko Baratta,
Mirko Baratta
IC Engines Advanced Laboratory
, Politecnico di Torino, c.so Duca degli Abruzzi, 24-10129 Torino, Italy
Search for other works by this author on:
Andrea E. Catania,
Andrea E. Catania
IC Engines Advanced Laboratory
, Politecnico di Torino, c.so Duca degli Abruzzi, 24-10129 Torino, Italy
Search for other works by this author on:
Stefano d’Ambrosio
Stefano d’Ambrosio
IC Engines Advanced Laboratory
, Politecnico di Torino, c.so Duca degli Abruzzi, 24-10129 Torino, Italy
Search for other works by this author on:
Mirko Baratta
IC Engines Advanced Laboratory
, Politecnico di Torino, c.so Duca degli Abruzzi, 24-10129 Torino, Italy
Andrea E. Catania
IC Engines Advanced Laboratory
, Politecnico di Torino, c.so Duca degli Abruzzi, 24-10129 Torino, Italy
Stefano d’Ambrosio
IC Engines Advanced Laboratory
, Politecnico di Torino, c.so Duca degli Abruzzi, 24-10129 Torino, ItalyJ. Eng. Gas Turbines Power. Nov 2008, 130(6): 062802 (11 pages)
Published Online: August 21, 2008
Article history
Received:
July 28, 2006
Revised:
March 12, 2008
Published:
August 21, 2008
Citation
Baratta, M., Catania, A. E., and d’Ambrosio, S. (August 21, 2008). "Nonlinear Versus Linear Stress-Strain Relations in Engine Turbulence Modeling Under Swirl and Squish Flow Conditions." ASME. J. Eng. Gas Turbines Power. November 2008; 130(6): 062802. https://doi.org/10.1115/1.2938274
Download citation file:
Get Email Alerts
Cited By
An Experimental Comparison of Methanol Combustion Strategies: Spark Ignition Versus Compression Ignition
J. Eng. Gas Turbines Power
Systems-Based Approach To Predicting Tbc Delamination Due To Cmas Infiltration
J. Eng. Gas Turbines Power
Related Articles
Implication of Mismatch Between Stress and Strain-Rate in Turbulence Subjected to Rapid Straining and Destraining on Dynamic LES Models
J. Fluids Eng (September,2005)
Heat Transfer Predictions for Two Turbine Nozzle Geometries at High Reynolds and Mach Numbers
J. Turbomach (April,1997)
Multidimensional Predictions of In-Cylinder Turbulent Flows: Contribution to the Assessment of k-ε Turbulence Model Variants for Bowl-in-Piston Engines
J. Eng. Gas Turbines Power (October,2005)
Related Proceedings Papers
Related Chapters
Fatigue Analysis in the Connecting Rod of MF285 Tractor by Finite Element Method
International Conference on Advanced Computer Theory and Engineering, 4th (ICACTE 2011)
Introduction I: Role of Engineering Science
Fundamentals of heat Engines: Reciprocating and Gas Turbine Internal Combustion Engines
Later Single-Cylinder Engines
Air Engines: The History, Science, and Reality of the Perfect Engine