One of the remedies to reduce the major emissions production of nitric oxide NOx, carbon monoxide (CO), and unburned hydrocarbon (UHC) from conventional gas turbine engine combustors at both high and low operating conditions without losing performance and stability is to use variable geometry combustors. This type of combustor configuration provides the possibility of dynamically controlling the airflow distribution of the combustor based on its operating conditions and therefore controlling the combustion in certain lean burn conditions. Two control schemes are described and analyzed in this paper: Both are based on airflow control with variable geometry, the second including fuel staging. A model two-spool turbofan engine is chosen in this study to test the effectiveness of the variable geometry combustor and control schemes. The steady and dynamic performance of the turbofan engine is simulated and analyzed using an engine transient performance analysis code implemented with the variable geometry combustor. Empirical correlations for NOx, CO, and UHC are used for the estimation of emissions. Some conclusions are obtained from this study: (1) with variable geometry combustors significant reduction of NOx emissions at high operating conditions and CO and UHC at low operating condition is possible; (2) combustion efficiency and stability can be improved at low operating conditions, which is symbolized by the higher flame temperature in the variable geometry combustor; (3) the introduced correlation between nondimensional fuel flow rate and air flow ratio to the primary zone is effective and simple in the control of flame temperature; (4) circumferential fuel staging can reduce the range of air splitter movement in most of the operating conditions from idle to maximum power and have the great potential to reduce the inlet distortion to the combustor and improve the combustion efficiency; and (5) during transient processes, the maximum moving rate of the hydraulic driven system may delay the air splitter movement but this effect on engine combustor performance is not significant.

1.
Wulff
,
A.
, and
Hourmouziadis
,
J.
,
1997
, “
Technology Review of Aeroengine Emissions
,”
Aerospace Science and Technology
, (
8
), pp.
557
572
.
2.
Schultz, D. F., 1975, “Ground Idle Performance Improvement of a Double-Annular Combustor by Using Simulated Variable Combustor Geometry,” NASA TM X-3176.
3.
Schultz, D. F., 1975, “Variable Combustor Geometry for Improving the Altitude Relight Capability of a Double Annular Combustor,” NASA TM X-3163.
4.
Cupta, A. K., Ramavajjala, M. S., and Chomiak, J., 1988, “Burner Geometry Effects on Combustion and NOx Emission Characteristics of Variable Geometry Swirl Combustor,” Paper No. AIAA-89-0488.
5.
Fletcher, R. S., 1973, “The Automotive Gas Turbine,” conference on Developments in Automotive Power Plants to Reduce Fuel Consumption, Air Pollution and Noise, Queen Mary College, London, Apr.
6.
Saintsbury, J. A., and Sampath, P., 1974, “Atmospheric Tests of a Variable Combustor Geometry for Reducing Gas Turbine Emissions,” ASME/CSME Conference, Montreal, May.
7.
Fletcher, R. S., and Adkins, R. C., 1976, “The Variable Geometry Combustor,” AGARD Conference (48 PEP Meeting), Paris, Sept.
8.
Hayashi, S., Yamada, H., and Shimodaira, K., 1996, “Engine Testing of a Natural Gas-Fired, Low-NOx, Variable Geometry Gas Turbine Combustor for a Small Gas Turbine,” ASME Paper No. 96-GT-455.
9.
Li, Y. G., and Hales, R. L., 2002, “Gas Turbine Emissions Control Using Variable Geometry Combustor and Fuel Staging,” Paper No. AIAA-2002-0079.
10.
Maccallum, N. R. L., 1984, “Computational Models for the Transient Performance of RB183-02 (Spey) and RB183-03 (Tay) Engines,” Technical Report RR/1, University of Glasgow, Aug. 13.
11.
Lefebvre, A. H., 1984, “Fuel Effects on Gas Turbine Combustion—Liner Temperature, Pattern Factor and Pollutant Emissions,” Paper No. AIAA-84-1491.
12.
Reeves, C. M., and Lefebvre, A. H., 1986, “Fuel Effects on Aircraft Combustor Emissions,” ASME Paper No. 86-GT-212.
13.
Gu¨lder
,
O¨. L.
,
1986
, “
Flame Temperature Estimation of Conventional and Future Jet Fuels
,”
ASME J. Eng. Gas Turbines Power
,
108
, pp.
376
380
.
14.
Steele
,
R. C.
,
Jarrett
,
A. C.
,
Malte
,
P. C.
,
Tonouchi
,
J. H.
, and
Nicol
,
D. G.
,
1997
, “
Variables Affecting NOx Formation in Lean-Premixed Combustion
,”
ASME J. Eng. Gas Turbines Power
,
119
, pp.
102
107
.
15.
Maccallum, N. R. L., and Qi, O. F., 1989, “The Transient Behavior of Aircraft Gas Turbines,” IMechE Seminar (Seminar S777) on Gas Turbines: Technology and Development, Institute of Mechanical Engineering, London, Nov.
16.
Pilidis, P., 1983, “Digital Simulation of Gas Turbine Performance,” Ph.D. dissertation, Department of Mechanical Engineering, University of Glasgow, Glasgow, Scotland.
You do not currently have access to this content.