The paper presents an analysis of the effect of ambient humidity on the performance of industrial gas turbines and examines the impact of humidity on methods used for engine condition assessment and fault diagnostics. First, the way of incorporating the effect of humidity into a computer model of gas turbine performance is described. The model is then used to derive parameters indicative of the “health” of a gas turbine and thus diagnose the presence of deterioration or faults. The impact of humidity magnitude on the values of these health parameters is studied and the uncertainty introduced, if humidity is not taken into account, is assessed. It is shown that the magnitude of the effect of humidity depends on ambient conditions and is more severe for higher ambient temperatures. Data from an industrial gas turbine are presented to demonstrate these effects and to show that if humidity is appropriately taken into account, the uncertainty in the estimation of health parameters is reduced.

1.
Andersen, H., 2000, “Early Detection of Combustor Pulsations and Optimized Operation Through On-Line Monitoring Systems,” ASME Paper No. 2000-GT-0180.
2.
Gu¨len, S. C., Griffin, P. R., and Paolucci, S., 2000, “Real-Time On-Line Performance Diagnostics of Heavy-Duty Industrial Gas Turbines,” ASME Paper No. 2000-GT-0312.
3.
Razak, A. M. Y, and Carlyle, J. S., 2000, “An Advanced Model Based Health Monitoring System To Reduce Gas Turbine Ownership Cost,” ASME Paper No. 2000-GT-627.
4.
Cloyd, S. T., and Harris, A. J., 1995, “Gas Turbine Performance—New Application and Test Correction Curves,” ASME Paper No. 95-GT-167.
5.
AGARD-AR-332,1995, Recommended Practices for the Assessment of the effects of Atmospheric Water Injestion on the Performance and Operability of Gas Turbines Engines, Sept.
6.
Bird, J., and Grabe, W., 1991, “Humidity Effects on Gas Turbine Performance,” ASME Paper No. 91-GT-329.
7.
Gu, Y. G., and Palmer, J. R., 1985, “A Mathematical Model for Computing the Effects of Air Humidity, Fuel Composition and Gas Dissociation on Gas Turbine Performance and Its Application,” ASME Paper No. 86-GT-114.
8.
Walsh, P. P., and Fletcher, P., 1998, Gas Turbine Performance, Blackwell Oxford, UK.
9.
Dundas, R., Sullivan, D., and Abegg, F., 1992, “Performance Monitoring of Gas Turbines for Failure Prevention,” ASME Paper No. 92-GT-267.
10.
Mathioudakis, K., Stamatis, A., Tsalavoutas, A., and Aretakis, N., 2001, “Performance Analysis of Industrial Gas Turbines for Engine Condition Monitoring,” ImechE J. Power Energy, 215(A2), p. 1.
11.
Lee, Y. H., and Singh R., 1996, “Health Monitoring of Turbine engine Gas Path Components and Measurements Instruments,” ASME Paper No. 96-GT-242.
12.
Stamatis
,
A.
,
Mathioudakis
,
K.
, and
Papailiou
,
K. D.
,
1990
, “
Adaptive Simulation of Gas Turbine Performance
,”
ASME J. Eng. Gas Turbines Power
,
112
, pp.
168
175
.
13.
Stamatis, A., Mathioudakis, K., Smith, M., and Papailiou, K. D., 1990, “Gas Turbine Component Fault Identification by Means of Adaptive Performance Modelling,” ASME Paper No. 90-GT-376.
14.
Tsalavoutas, A., Aretakis, N., Stamatis, A., and Mathioudakis, K., 2000, “Combining Advanced Data Analysis Methods for the Constitution of an Integrated Gas Turbine Condition Monitoring ans Diagnostic System,” ASME Paper No. 2000-GT-0034.
15.
Tsalavoutas, A., Pothos, S., Mathioudakis, K., and Stamatis, A., 1999, “Monitoring the Performance of a Twin-Shaft Ship Propulsion Turbine by Means of Adaptive Modeling,” RTO Symposium on Gas Turbine Operation and Technology for Land, Sea and Air Propulsion and Power Systems, Ottawa, Oct. 18–21.
16.
Meher-Homji, C. B., and Mee, T. R., III, 2000, “Inlet Fogging of Gas Turbine Engines: Part A—Theory, Psychrometrics and Fog Generation,” ASME Paper No. 2000-GT-307.
You do not currently have access to this content.